频道栏目
首页 > 资讯 > 交换机 > 正文

CISCO交换机配置100例

15-10-20        来源:[db:作者]  
收藏   我要投稿
switch>          用户模式
1:进入特权模式   enable
switch> enable
switch#
 
2:进入全局配置模式   configure terminal
switch> enable
switch#c onfigure terminal
switch(conf)#
 
3:交换机命名 hostnameaptech2950      以aptech2950为例
switch> enable
switch#c onfigure terminal
switch(conf)#hostname aptch-2950
aptech2950(conf)#
 
4:配置使能口令   enable passwordcisco     以cisco为例
switch> enable
switch#c onfigure terminal
switch(conf)#hostname aptch2950
aptech2950(conf)# enable password cisco
 
5:配置使能密码   enable secretciscolab     以cicsolab为例
switch> enable
switch#c onfigure terminal
switch(conf)#hostname aptch2950
aptech2950(conf)# enable secret ciscolab
 
6:设置虚拟局域网vlan 1    interface vlan 1
switch> enable
switch#c onfigure terminal
switch(conf)#hostname aptch2950
aptech2950(conf)# interface vlan 1
aptech2950(conf-if)#ip address 192.168.1.1255.255.255.0       配置交换机端口ip和子网掩码
aptech2950(conf-if)#noshut                              是配置处于运行中
aptech2950(conf-if)#exit
aptech2950(conf)#ip default-gateway192.168.254             设置网关地址
 
7:进入交换机某一端口 interface fastehernet0/17            以17端口为例
switch> enable
switch#c onfigure terminal
switch(conf)#hostname aptch2950
aptech2950(conf)# interface fastehernet 0/17
aptech2950(conf-if)#
 
8:查看命令   show
switch> enable
switch# show version   察看系统中的所有版本信息
show interface vlan 1   查看交换机有关ip 协议的配置信息
show running-configure 查看交换机当前起作用的配置信息
show interface fastethernet 0/1   察看交换机1接口具体配置和统计信息
show mac-address-table         查看mac地址表
show mac-address-table aging-time   查看mac地址表自动老化时间
 
9:交换机恢复出厂默认恢复命令  
switch> enable
switch# erase startup-configure
switch# reload
 
 
 
10:双工模式设置
switch> enable
switch#c onfigure terminal
switch2950(conf)#hostname aptch-2950
aptech2950(conf)# interface fastehernet0/17                 以17端口为例
aptech2950(conf-if)#duplexfull/half/auto                    有full , half, auto 三个可选项
 
11:cdp相关命令
switch> enable
switch# show cdp     查看设备的cdp全局配置信息
show cdp interface fastethernet 0/17     查看17端口的cdp配置信息
show cdp traffic      查看有关cdp包的统计信息
show cdp nerghbors   列出与设备相连的cisco设备
 
12:csico2950的密码恢复
拔下交换机电源线。
用手按着交换机的MODE键,插上电源线
在switch:后执行flash_ini命令:switch: flash_ini
查看flash中的文件: switch: dir flash:
把“config.text”文件改名为“config.old”: switch: rename flash: config.text flash: config.old
执行boot:   switch: boot
交换机进入是否进入配置的对话,执行no : 
进入特权模式察看flash里的文件: show flash :
把“config.old”文件改名为“config.text”:    switch: rename flash:config.old flash: config.text
把“config.text”拷入系统的“running-configure”: copy flash: config.text system : running-configure
把配置模式重新设置密码存盘,密码恢复成功。
 
13:交换机telnet远程登录设置:
switch>en
switch#c onfigure terminal
switch(conf)#hostname aptech-2950
aptech2950(conf)#enable passwordcisco           以cisco为特权模式密码
aptech2950(conf)#interface fastethernet0/1         以17端口为telnet远程登录端口
aptech2950(conf-if)#ip address 192.168.1.1 255.255.255.0
aptech2950(conf-if)#no shut
aptech2950(conf-if)#exit
aptech2950(conf)line vty 04                   设置0-4 个用户可以telnet远程登陆
aptech2950(conf-line)#login
aptech2950(conf-line)#passwordedge             以edge为远程登录的用户密码
主机设置:
ip         192.168.1.2               主机的ip必须和交换机端口的地址在同一网络段
netmask     255.255.255.0
gate-way   192.168.1.1               网关地址是交换机端口地址
运行:
telnet 192.168.1.1 
进入telnet远程登录界面
password :edge                
aptech2950>en
password: cisco
aptech#
 
14:交换机配置的重新载入和保存
设置完成交换机的配置后:
aptech2950(conf)#reload
是否保存(y/n)    y: 保存设置信息         n:不保存设置信息
 
 
1.在基于IOS的交换机上设置主机名/系统名: 
switch(config)# hostname hostname 
在基于CLI的交换机上设置主机名/系统名: 
switch(enable) set system name name-string
2.在基于IOS的交换机上设置登录口令: 
switch(config)# enable password level 1 password 
在基于CLI的交换机上设置登录口令: 
switch(enable) set password 
switch(enable) set enalbepass
3.在基于IOS的交换机上设置远程访问: 
switch(config)# interface vlan 1 
switch(config-if)# ip address ip-address netmask 
switch(config-if)# ip default-gateway ip-address 
在基于CLI的交换机上设置远程访问: 
switch(enable) set interface sc0 ip-address netmask broadcast-address 
switch(enable) set interface sc0 vlan 
switch(enable) set ip route default gateway
4.在基于IOS的交换机上启用和浏览CDP信息: 
switch(config-if)# cdp enable 
switch(config-if)# no cdp enable 
为了查看Cisco邻接设备的CDP通告信息: 
switch# show cdp interface [type modle/port] 
switch# show cdp neighbors [type module/port] [detail] 
在基于CLI的交换机上启用和浏览CDP信息: 
switch(enable) set cdp {enable|disable} module/port 
为了查看Cisco邻接设备的CDP通告信息: 
switch(enable) show cdp neighbors[module/port] [vlan|duplex|capabilities|detail]
5.基于IOS的交换机的端口描述: 
switch(config-if)# description description-string 
基于CLI的交换机的端口描述: 
switch(enable)set port name module/number description-string
6.在基于IOS的交换机上设置端口速度: 
switch(config-if)# speed{10|100|auto} 
在基于CLI的交换机上设置端口速度: 
switch(enable) set port speed moudle/number {10|100|auto} 
switch(enable) set port speed moudle/number {4|16|auto}
7.在基于IOS的交换机上设置以太网的链路模式: 
switch(config-if)# duplex {auto|full|half} 
在基于CLI的交换机上设置以太网的链路模式: 
switch(enable) set port duplex module/number {full|half}
8.在基于IOS的交换机上配置静态VLAN: 
switch# vlan database 
switch(vlan)# vlan vlan-num name vla
switch(vlan)# exit 
switch# configure teriminal 
switch(config)# interface interface module/number 
switch(config-if)# switchport mode access 
switch(config-if)# switchport access vlan vlan-num 
switch(config-if)# end 
在基于CLI的交换机上配置静态VLAN:
switch(enable) set vlan vlan-num [name name] 
switch(enable) set vlan vlan-num mod-num/port-list
9. 在基于IOS的交换机上配置VLAN中继线: 
switch(config)# interface interface mod/port 
switch(config-if)# switchport mode trunk 
switch(config-if)# switchport trunk encapsulation {isl|dotlq} 
switch(config-if)# switchport trunk allowed vlan remove vlan-list 
switch(config-if)# switchport trunk allowed vlan add vlan-list 
在基于CLI的交换机上配置VLAN中继线: 
switch(enable) set trunk module/port [on|off|desirable|auto|nonegotiate] 
Vlan-range [isl|dotlq|dotl0|lane|negotiate]
10.在基于IOS的交换机上配置VTP管理域: 
switch# vlan database 
switch(vlan)# vtp domain domain-name 
在基于CLI的交换机上配置VTP管理域: 
switch(enable) set vtp [domain domain-name]
11.在基于IOS的交换机上配置VTP模式: 
switch# vlan database 
switch(vlan)# vtp domain domain-name 
switch(vlan)# vtp {sever|cilent|transparent} 
switch(vlan)# vtp password password 
在基于CLI的交换机上配置VTP 模式: 
switch(enable) set vtp [domain domain-name] [mode{ sever|cilent|transparent}][password password]
12. 在基于IOS的交换机上配置VTP版本: 
switch# vlan database 
switch(vlan)# vtp v2-mode 
在基于CLI的交换机上配置VTP版本: 
switch(enable) set vtp v2 enable
13. 在基于IOS的交换机上启动VTP剪裁: 
switch# vlan database 
switch(vlan)# vtp pruning 
在基于CL I 的交换机上启动VTP剪裁: 
switch(enable) set vtp pruning enable
14.在基于IOS的交换机上配置以太信道: 
switch(config-if)# port group group-number [distribution {source|destination}] 
在基于CLI的交换机上配置以太信道: 
switch(enable) set port channel moudle/port-range mode{on|off|desirable|auto}
15.在基于IOS的交换机上调整根路径成本: 
switch(config-if)# spanning-tree [vlan vlan-list] cost cost 
在基于CLI的交换机上调整根路径成本:
switch(enable) set spantree portcost moudle/port cost 
switch(enable) set spantree portvlancost moudle/port [cost cost][vlan-list]
16.在基于IOS的交换机上调整端口ID: 
switch(config-if)# spanning-tree[vlan vlan-list]port-priority port-priority 
在基于CLI的交换机上调整端口ID: 
switch(enable) set spantree portpri {mldule/port}priority 
switch(enable) set spantree portvlanpri {module/port}priority [vlans]
17. 在基于IOS的交换机上修改STP时钟: 
switch(config)# spanning-tree [vlan vlan-list] hello-time seconds 
switch(config)# spanning-tree [vlan vlan-list] forward-time seconds 
` switch(config)# spanning-tree [vlan vlan-list] max-age seconds 
在基于CLI的交换机上修改STP时钟: 
switch(enable) set spantree hello interval[vlan] 
switch(enable) set spantree fwddelay delay [vlan] 
switch(enable) set spantree maxage agingtiame[vlan]
18. 在基于IOS的交换机端口上启用或禁用Port Fast 特征: 
switch(config-if)#spanning-tree portfast 
在基于CLI的交换机端口上启用或禁用Port Fast 特征: 
switch(enable) set spantree portfast {module/port}{enable|disable}
19. 在基于IOS的交换机端口上启用或禁用UplinkFast 特征: 
switch(config)# spanning-tree uplinkfast [max-update-rate pkts-per-second] 
在基于CLI的交换机端口上启用或禁用UplinkFast 特征: 
switch(enable) set spantree uplinkfast {enable|disable}[rate update-rate][all-protocols off|on]
20. 为了将交换机配置成一个集群的命令交换机,首先要给管理接口分配一个IP地址,然后使用下列命令:switch(config)# cluster enable cluster-name
21. 为了从一条中继链路上删除VLAN,可使用下列命令: 
switch(enable) clear trunk module/port vlan-range
22. 用show vtp domain 显示管理域的VTP参数.
23. 用show vtp statistics显示管理域的VTP参数.
24. 在Catalyst交换机上定义TrBRF的命令如下: 
switch(enable) set vlan vlan-name [name name] type trbrf bridge bridge-num[stp{ieee|ibm}]
25. 在Catalyst交换机上定义TrCRF的命令如下: 
switch (enable) set vlan vlan-num [name name] type trcrf 
{ring hex-ring-num|decring decimal-ring-num} parent vlan-num
26. 在创建好TrBRF VLAN之后,就可以给它分配交换机端口.对于以太网交换,可以采用如下命令给VLAN分配端口: 
switch(enable) set vlan vlan-num mod-num/port-num
27. 命令show spantree显示一个交换机端口的STP状态.
28. 配置一个ELAN的LES和BUS,可以使用下列命令: 
ATM (config)# interface atm number.subint multioint 
ATM(config-subif)# lane serber-bus ethernet elan-name
29. 配置LECS: 
ATM(config)# lane database database-name 
ATM(lane-config-databade)# name elan1-name server-atm-address les1-nsap-address
ATM(lane-config-databade)# name elan2-name server-atm-address les2-nsap-address
ATM(lane-config-databade)# name …
30. 创建完数据库后,必须在主接口上启动LECS.命令如下: 
ATM(config)# interface atm number 
ATM(config-if)# lane config database database-name 
ATM(config-if)# lane config auto-config-atm-address
31. 将每个LEC配置到一个不同的ATM子接口上.命令如下: 
ATM(config)# interface atm number.subint multipoint 
ATM(config)# lane clientethernet vlan-num elan-num
32. 用show lane server 显示LES的状态.
33. 用show lane bus显示bus的状态.
34. 用show lane database显示LECS数据库可内容.
35. 用show lane client显示LEC的状态.
36. 用show module显示已安装的模块列表.
37. 用物理接口建立与VLAN的连接: 
router# configure terminal 
router(config)# interface media module/port 
router(config-if)# description description-string 
router(config-if)# ip address ip-addr subnet-mask 
router(config-if)# no shutdown
38. 用中继链路来建立与VLAN的连接: 
router(config)# interface module/port.subinterface 
router(config-ig)# encapsulation[isl|dotlq] vlan-number 
router(config-if)# ip address ip-address subnet-mask
39. 用LANE 来建立与VLAN的连接: 
router(config)# interface atm module/port 
router(config-if)# no ip address 
router(config-if)# atm pvc 1 0 5 qsaal 
router(config-if)# atm pvc 2 0 16 ilni 
router(config-if)# interface atm module/port.subinterface multipoint 
router(config-if)# ip address ip-address subnet-mask 
router(config-if)# lane client ethernet elan-num 
router(config-if)# interface atm module/port.subinterface multipoint 
router(config-if)# ip address ip-address subnet-name 
router(config-if)# lane client ethernet elan-name 
router(config-if)# …
40. 为了在路由处理器上进行动态路由配置,可以用下列IOS命令来进行: 
router(config)# ip routing 
router(config)# router ip-routing-protocol 
router(config-router)# network ip-network-number 
router(config-router)# network ip-network-number
41. 配置默认路由: 
switch(enable) set ip route default gateway
42. 为一个路由处理器分配VLANID,可在接口模式下使用下列命令: 
router(config)# interface interface number 
router(config-if)# mls rp vlan-id vlan-id-num
43. 在路由处理器启用MLSP: 
router(config)# mls rp ip
44. 为了把一个外置的路由处理器接口和交换机安置在同一个VTP域中: 
router(config)# interface interface number 
router(config-if)# mls rp vtp-domain domain-name
45. 查看指定的VTP域的信息:
router# show mls rp vtp-domain vtp domain name
46. 要确定RSM或路由器上的管理接口,可以在接口模式下输入下列命令: 
router(config-if)#mls rp management-interface
47. 要检验MLS-RP的配置情况: 
router# show mls rp
48. 检验特定接口上的MLS配置: 
router# show mls rp interface interface number
49. 为了在MLS-SE上设置流掩码而又不想在任一个路由处理器接口上设置访问列表: 
set mls flow [destination|destination-source|full]
50. 为使MLS和输入访问列表可以兼容,可以在全局模式下使用下列命令: 
router(config)# mls rp ip input-acl
51. 当某个交换机的第3层交换失效时,可在交换机的特权模式下输入下列命令: 
switch(enable) set mls enable
52. 若想改变老化时间的值,可在特权模式下输入以下命令: 
switch(enable) set mls agingtime agingtime
53. 设置快速老化: 
switch(enable) set mls agingtime fast fastagingtime pkt_threshold
54. 确定那些MLS-RP和MLS-SE参与了MLS,可先显示交换机引用列表中的内容再确定: 
switch(enable) show mls include
55. 显示MLS高速缓存记录: 
switch(enable) show mls entry
56. 用命令show in arp显示ARP高速缓存区的内容。
57. 要把路由器配置为HSRP备份组的成员,可以在接口配置模式下使用下面的命令: 
router(config-if)# standby group-number ip ip-address
58. 为了使一个路由器重新恢复转发路由器的角色,在接口配置模式下: 
router(config-if)# standy group-number preempt
59. 访问时间和保持时间参数是可配置的: 
router(config-if)# standy group-number timers hellotime holdtime
60. 配置HSRP跟踪: 
router(config-if)# standy group-number track type-number interface-priority
61. 要显示HSRP路由器的状态: 
router# show standby type-number group brief
62. 用命令show ip igmp确定当选的查询器。
63. 启动IP组播路由选择: 
router(config)# ip muticast-routing
64. 启动接口上的PIM: 
dalllasr1>(config-if)# ip pim {dense-mode|sparse-mode|sparse-dense-mode}
65. 启动稀疏-稠密模式下的PIM: 
router# ip multicast-routing 
router# interface type number 
router# ip pim sparse-dense-mode
66. 核实PIM的配置: 
dallasr1># show ip pim interface[type number] [count]
67. 显示PIM邻居: 
dallasr1># show ip neighbor type number
68. 为了配置RP的地址,命令如下: 
dallasr1># ip pim rp-address ip-address [group-access-list-number][override]
69. 选择一个默认的RP: 
dallasr1># ip pim rp-address 
通告RP和它所服务的组范围: 
dallasr1># ip pim send-rp-announce type number scope ttl group-listaccess-list-number 
为管理范围组通告RP的地址: 
dallasr1># ip pim send-rp-announce ethernet0 scope 16 group-list1 
dallasr1># access-list 1 permit 266.0.0.0 0.255.255.255 
设定一个RP映像代理: 
dallasr1># ip pim send-rp-discovery scope ttl 
核实组到RP的映像: 
dallasr1># show ip pim rp mapping 
dallasr1># show ip pim rp [group-name|group-address] [mapping]
70. 在路由器接口上用命令ip multicast ttl-thresholdttl-value设定TTL阀值: 
dallasr1>(config-if)# ip multicast ttl-threshold ttl-value
71. 用show ip pim neighbor显示PIM邻居表。
72. 显示组播通信路由表中的各条记录: 
dallasr1>show ip mroute[group-name|group-address][scoure][summary][count][active kbps]
73. 要记录一个路由器接受和发送的全部IP组播包: 
dallasr1> #debug ip mpacket [detail] [access-list][group]
74. 要在CISCO路由器上配置CGMP: 
dallasr1>(config-if)# ip cgmp
75.配置一个组播路由器,使之加入某一个特定的组播组: 
dallasr1>(config-if)# ip igmp join-group group-address
76. 关闭 CGMP: 
dallasr1>(config-if)# no ip cgmp
77. 启动交换机上的CGMP: 
dallasr1>(enable) set cgmp enable
78. 核实Catalyst交换机上CGMP的配置情况: 
catalystla1>(enable) show config 
set prompt catalystla1> 
set interface sc0 192.168.1.1 255.255.255.0 
set cgmp enable
79. CGMP离开的设置: 
Dallas_SW(enable) set cgmp leave
80. 在Cisco设备上修改控制端口密码: 
R1(config)# line console 0 
R1(config-line)# login 
R1(config-line)# password Lisbon 
R1(config)# enable password Lilbao 
R1(config)# login local 
R1(config)# username student password cisco
81. 在Cisco设备上设置控制台及vty端口的会话超时: 
R1(config)# line console 0 
R1(config-line)# exec-timeout 5 10 
R1(config)# line vty 0 4 
R1(config-line)# exec-timeout 5 2
82. 在Cisco设备上设定特权级: 
R1(config)# privilege configure level 3 username 
R1(config)# privilege configure level 3 copy run start 
R1(config)# privilege configure level 3 ping 
R1(config)# privilege configure level 3 show run 
R1(config)# enable secret level 3 cisco
83. 使用命令privilege 可定义在该特权级下使用的命令: 
router(config)# privilege mode level level command
84. 设定用户特权级: 
router(config)# enable secret level 3 dallas 
router(config)# enable secret san-fran 
router(config)# username student password cisco
85. 标志设置与显示: 
R1(config)# banner motd ‘unauthorized access will be prosecuted!’
86. 设置vty访问: 
R1(config)# access-list 1 permit 192.168.2.5 
R1(config)# line vty 0 4 
R1(config)# access-class 1 in
87. 配置HTTP访问: 
Router3(config)# access-list 1 permit 192.168.10.7 
Router3(config)# ip http sever 
Router3(config)# ip http access-class 1 
Router3(config)# ip http authentication local 
Router3(config)# username student password cisco
88. 要启用HTTP访问,请键入以下命令: 
switch(config)# ip http sever
89. 在基于set命令的交换机上用setCL1启动和核实端口安全: 
switch(enable) set port security mod_num/port_num…enable mac address 
switch(enable) show port mod_num/port_num 
在基于CiscoIOS命令的交换机上启动和核实端口安全: 
switch(config-if)# port secure [mac-mac-count maximum-MAC-count] 
switch# show mac-address-table security [type module/port]
90. 用命令access-list在标准通信量过滤表中创建一条记录: 
Router(config)# access-list access-list-number {permit|deny} source-address[source-address]
91. 用命令access-list在扩展通信量过滤表中创建一条记录: 
Router(config)# access-list access-list-number {permit|deny{protocol|protocol-keyword}}{sourcesource-wildcard|any}{destination destination-wildcard|any}[protocol-specificoptions][log]
92. 对于带内路由更新,配置路由更新的最基本的命令格式是: 
R1(config-router)#distribute-list access-list-number|name in [type number]
93. 对于带外路由更新,配置路由更新的最基本的命令格式是: 
R1(config-router)#distribute-list access-list-number|name out [interface-name]routing-process| autonomous-system-number
94. set snmp命令选项: 
set snmp community {read-only|ready-write|read-write-all}[community_string]
95. set snmp trap 命令格式如下: 
set snmp trap {enable|disable} 
[all|moudle|classis|bridge|repeater| auth|vtp|ippermit|vmps|config|entity|stpx]
set snmp trap rvcr_addr rcvr_community
96. 启用SNMP chassis 陷阱: 
Console>(enable) set snmp trap enable chassis
97. 启用所有SNMP chassis 陷阱: 
Console>(enable) set snmp trap enable
…………以下由about于2002年12月6日增加…………
98. 禁用SNMP chassis 陷阱:
Console>(enable) set snmp trap disable chassis
99. 给SNMP陷阱接收表加一条记录:
Console>(enable) set snmp trap 192.122.173.42 public
100. show snmp 输出结果。
101. 命令set snmp rmon enable 的输出结果。
102. 显示SPAN信息:
Consile> show span
相关TAG标签
上一篇:谈谈自己对C语言中函数指针的一些理解
下一篇:工具函数分析
相关文章
图文推荐

关于我们 | 联系我们 | 广告服务 | 投资合作 | 版权申明 | 在线帮助 | 网站地图 | 作品发布 | Vip技术培训 | 举报中心

版权所有: 红黑联盟--致力于做实用的IT技术学习网站