linux-2.6.35内核移植——Nand flash驱动的移植
linux-2.6.35内核移植——Nand flash驱动的移植
Nand flash 是嵌入式系统最常用的外部存储设备，这里介绍Nand flash驱动移植的过程。
一、移植环境：
1、 Ubuntu 10.10发行版
2、 u-boot.bin
3、 FS_S5PC100平台
4、 交叉编译器： arm-cortex_a8-linux-gnueabi-gcc
---------------------------------------------------------------------
二、移植步骤
在linux-2.6.35.2的内核中已经包含了s3c2410的nand flash控制器的驱动，但是需要我们正确配置后才能正常工作。
1、添加针对FS_S5PC100平台上的Nand flash驱动
拷贝 s3c_nand.c http://download.csdn.net/detail/baby_afu/4412870到drivers/mtd/nand下
拷贝 regs-nand.h http://download.csdn.net/detail/baby_afu/4412873到 arch/arm/mach-s5pc100/include/mach下
2、针对FS_S5PC100平台上的nand flash 设备，修改driver/mtd/nand/nand_base.c
第2812行 www.2cto.com
/* Read entire ID string */
for (i = 0; i < 8; i++)
为
/* Read entire ID string */
for (i = 0; i < 5; i++)
3、添加内核配置选项
修改driver/mtd/nand/Kconfig添加如下内容：
config MTD_NAND_S3C
tristate "NAND Flash support for S3C Soc"
depends on (ARCH_S3C64XX || ARCH_S5P64XX || ARCH_S5PC1XX || ARCH_S5PC100) && MTD_NAND
help
This enables the NAND flash controller on the S3C.
No board specfic support is done by this driver , each board
must advertise a platform_device for the driver to attach.
config MTD_NAND_S3C_DEBUG
bool "S3C NAND driver debug"
depends on MTD_NAND_S3C
help
Enable debugging of the S3C NAND driver
config MTD_NAND_S3C_HWECC
bool "S3C NAND Hardware ECC"
depends on MTD_NAND_S3C
help www.2cto.com
Enable the use of the S3C's internal ECC generator when
using NAND. Early versons of the chip have had problems with
incorrect ECC generation, and if using these, the default of
software ECC is preferable
If you lay down a device with the hardware ECC, the you will
currently not be able to switch to software, as there is no
implementation for ECC method used by the S3C
修改drivers/mtd/nand/Makefile添加如下内容：
obj-$(CONFIG_MTD_NAND_S3C) += s3c_nand.o
4、修改平台代码
修改arch/arm/mach-s5pc100/mach-smdkc100.c添加如下内容：
添加头文件
#if defined(CONFIG_MTD_NAND_S3C)
#include <linux/mtd/partitions.h>
#include <linux/mtd/mtd.h>
#include <plat/nand.h>
#endif
添加平台设备
/** Nand flash Support **/
#if defined(CONFIG_MTD_NAND_S3C)
static struct mtd_partition s5pc100_nand_part[] = {
[0] = {
.name = "bootloader",
.size = SZ_1M,
.offset = 0,
},
[1] = {
.name = "kernel",
.offset = MTDPART_OFS_APPEND,
.size = SZ_1M*3,
}, www.2cto.com
[2] = {
.name = "roorfs",
.offset = MTDPART_OFS_APPEND,
.size = SZ_1M * 100,
},
[3] = {
.name = "usrfs",
.offset = MTDPART_OFS_APPEND,
.size = MTDPART_SIZ_FULL,
},
};
struct s3c_nand_mtd_info s5pc100_nand_mtd_part_info = {
.chip_nr = 1,
.mtd_part_nr = ARRAY_SIZE(s5pc100_nand_part),
.partition = s5pc100_nand_part,
};
static struct resource s5pc100_nand_resource[] = {
[0] = {
.start = 0xE7200000,
.end = 0xE7200000 + SZ_1M,
.flags = IORESOURCE_MEM,
},
};
struct platform_device s5pc100_device_nand = {
.name = "s5pc100-nand",
.id = -1,
.num_resources = ARRAY_SIZE(s5pc100_nand_resource),
.resource = s5pc100_nand_resource,
.dev = {
.platform_data = &s5pc100_nand_mtd_part_info,
},
};
#endif
添加平台设备列表
在smdkc100_device[]结构体数组中添加如下内容：
#if defined(CONFIG_MTD_NAND_S3C)
&s5pc100_device_nand,
#endif www.2cto.com
修改 arch/arm/plat-samsung/include/plat/nand.h 添加如下内容：
struct s3c_nand_mtd_info {
uint chip_nr;
uint mtd_part_nr;
struct matd_partition *partition;
};
5、 配置内核
$ make menuconfig
修改
Device Drivers --->
<*> Memory Technology Device (MTD) support --->
[*] MTD partitioning support
<*> Caching block device access to MTD devices
<*> NAND Device Support --->
<*> NAND Flash support for S3C SoCs
[*] S3C NAND Hardware ECC
File System --->
Partition Types --->
[*] Advanced partitioin selection
[*] PC BIOS (MSDOS partition tables) support
[*] BSD disklabel (FreeBSD partition tables) support
---------------------------------------------------------------------
三、编译内核并拷贝到tftpboot下
$ make zImage www.2cto.com
$ cp arch/arm/boot/zImage /tftpboot
---------------------------------------------------------------------
四、测试
启动目标板，查看系统信息：
# cat /proc/mtd
dev: size erasesize name
mtd0: 00100000 00020000 "bootloader"
mtd1: 00300000 00020000 "kernel"
mtd2: 00400000 00020000 "rootfs"
mtd3: 0f800000 00020000 "usrfs"
作者 lr_ting
相关文章
图文推荐
- 文章
- 推荐
- 热门新闻